Bill of Materials

Plastic Parts

  • 2x Root 2 CNC – Y gantry assm-1 Y-Axis Belt Clamp GT2
  • 4x Root 2 CNC – Y gantry assm-1 Y Motion Bearing Mount
  • 1x Root 2 CNC – Y gantry assm-1 Y Drag Chain Carriage
  • 1x Root 2 CNC – Y gantry assm-1 X-Axis Carriage Y Drag Chain Mount
  • 1x Root 2 CNC – Y gantry assm-1 X-Axis Carriage Y Drag Chain Mount Idler
  • 2x Root 2 CNC – Y gantry assm-1 X-Axis Belt Clamp
  • 2x Root 2 CNC – Y gantry assm-1 X-Axis Box Bar Mount
  • 2x Root 2 CNC – Y gantry assm-1 Dirt Cover
  • 1x Root 2 CNC – X carriage-1 Z-Axis Motor Mount
  • 1x Root 2 CNC – X carriage-1 Z carriage-1 Spindle Upper Clamp
  • 1x Root 2 CNC – X carriage-1 Z carriage-1 Spindle Lower Clamp
  • 1x Root 2 CNC – X carriage-1 X-Axis Motor Mount
  • 1x Root 2 CNC – X carriage-1 X-Axis Carriage Drag Chain Mount Idler
  • 2x Root 2 CNC – X carriage-1 linear rail 90 bearing mount Y-Axis Carriage
  • 1x Root 2 CNC – X carriage-1 3M Pulley 32T 5mm
  • 1x Root 2 CNC – X carriage-1 3M Pulley 22T 8mm
  • 1x Root 2 CNC – Ramps controller-1 Ramps Case Lid
  • 1x Root 2 CNC – Ramps controller-1 Ramps Case Base
  • 1x Root 2 CNC – Base and Y axis assm-1 Y-Axis Bar Mount
  • 1x Root 2 CNC – Base and Y axis assm-1 Y-Axis Bar Mount Idler
  • 1x Root 2 CNC – Base and Y axis assm-1 Y-Axis Bar Mount Idler Mirror
  • 1x Root 2 CNC – Base and Y axis assm-1 Y-Axis Bar Mount Mirror
  • 1x Root 2 CNC – Base and Y axis assm-1 Y-Axis Motor Mount
  • 1x Root 2 CNC – Base and Y axis assm-1 Y-Axis Motor Mount Mirror
  • 1x Root 2 CNC – Base and Y axis assm-1 Y-Axis Drag Chain
  • 1x Root 2 CNC – Base and Y axis assm-1 3M Pulley 48T 8mm
  • 1x Root 2 CNC – Base and Y axis assm-1 3M Pulley 24T 5mm
  • 4x Root 2 CNC – Base and Y axis assm- Foot

Electronics

  • 1x Arduino Mega + Ramps 1.4
  • 3x DRV8825 (Optional but preferred over the A4988)
  • 3x Nema 17 Stepper motors (Get the Highest torque possible)
  • 1x 60mm DC Fan
  • 6x Endstop micro switches (KW11 I drilled the whole to 3mm to screw then in to the plastic parts)
  • 1x DC Spindle (52mm Diameter – Get the highest wattage, you will be thank full later on)
  • 1x Diode This is needed if using the heatbed Mosfet on the ramps to control the spindle – google Mosfet switching inductive loads for more information
  • 4 core AWG26 cable (use for motor wiring and endstops)

Fixings

  • 4x M8 Penny washers
  • Lots of M8 Standard washers
  • lots of M8 Nuts
  • 24x M8 x 25mm Bolts
  • 2x M8 x 35-40mm Bolt
  • 16x M8 Tee Nuts
  • 2x M4 x 50mm Bolt
  • 16x M4 Nuts
  • 16x M4 Washer
  • 16x M4 x 40mm Bolt
  • Lots of M3 9mm Penny Washers
  • Lots of M3 Nuts
  • 10x M3 x 10mm
  • lots M3 x 16,20,25,30,40 mm Lengths (good to have a selection on hand)

Bearings

  • 36x 608 Bearings
  • 4x LM10UU

Metal Work

  • 2x Aluminum Box section (X-Axis) 25x25x496x3mm (W,D,L,T)
  • 2x Aluminum Box section (Y-Axis) 25x25x496x3mm (W,D,L,T)
  • 1x M8 Smooth Rod 580mm
  • 8x M8 Threaded Rod 85 mm
  • 1x M8 Threaded Rod 500 mm
  • 2x M8 Threaded Rod 200 mm
  • 1x M8 Threaded Rod 230 mm
  • 2x M8 Threaded Rod 100 mm
  • 2x M10 Smooth Rod 185 mm

Motion

  • GT2 Belt (Length depending on size of the of the machine)
  • 2x GT2 36T Pulley 8mm Bore
  • 1x 3M-210T-06 Belt
  • 1x 3M-264T-06 HTD
  • 1x GT2 16T Pulley 5mm Bore
  • 2x Drag Chain 20 x 10 mm 1m Length

Wood

  • 2x Wood Side Panel
  • 1x Wood Base